Balle Racing Mountain Bike Parts & Tools

We Sell Hadley hubs

SDH Freehub Bearing/Rebuild Kit Shimano Style 2018+

50.00
HadleyFreehubRebuildS11-XD.jpg
HadleyFreehubShimanoXD.jpg

SDH Freehub Bearing/Rebuild Kit Shimano Style 2018+

50.00

Hadley Freehub Bearing/Rebuild Kit 2018+ SDH Shimano style freehubs with XD style internal axle Does not work with older 2001 - 2017 Shimano style internal axle.

Includes Freehub Bearings Ball & Needle, Spacer, Pawls, Spring, Retainer, Seals and 30cc of Teflon PTFE Oil.

Works with Hadley SDH and SDH-XL hubs 2018 and newer or older hub that has a XD internal axle.

3 pawl 36 point or 4 pawl 72 point.

Hadley No. KIT-S11/XD

More Info

Quantity:
2 available
Add To Cart

Hadley Freehub Bearing/Rebuild Kit 2018+ SDH Shimano style freehubs with XD style internal axle Does not work with older 2001 - 2017 Shimano style internal axle.

Includes Freehub Bearings Ball & Needle, Spacer, Pawls, Spring, Retainer, Seals and 30cc of Teflon PTFE Oil.

Works with Hadley SDH and SDH-XL hubs 2018 and newer or older hub that has a XD internal axle.

3 pawl 36 point or 4 pawl 72 point.

Hadley No. KIT-S11/XD

Recommend using Hadley Wrench Kit T600200

Also use light Teflon® fortified oil on freehub pawls

See photo of gold and red hub, the gold hub on the left is the 2001 to 2017 where the end cap tapers out to a larger diameter at the base, note the inside diameter of the white plastic retainer is larger where the six pin spanner holes are right next to the inside diameter. The red hub on the right has the 2018 and newer Shimano/XD freehub where the end cap is a straight cylinder and does not flare out to a larger diameter, also note the white plastic retainer has a smaller inside diameter and the six pin spanner holes are farther from the inside diameter. If you have the red style hub this rebuild kit will work with your freehub. If you have the gold style freehub you have the older 2001 to 2017 and need the KIT-SDH

FREEHUB ASSEMBLY –
1. REMOVE NEEDLE SLEEVE, NEEDLE BEARING AND SPACER FROM INSIDE
FREEHUB BODY. NEXT, REMOVE WHITE RETAINING RING FROM FREEHUB
BODY.
2. PRESS OUT OLD FREEHUB BALL BEARING. REMOVE PAWLS AND SPRING AND
MAKE SURE THAT PAWL POCKETS AND INSIDE THE FREEHUB BODY HAVE
BEEN CLEANED. APPLY SOME HIGH PRESSURE LUBE INSIDE FREEHUB BODY
AND THEN PRESS NEW BALL BEARING ASSEMBLY BACK INTO FREEHUB BODY.
ONCE IT IS PRESSED IN, THREAD IN THE NEW WHITE RETAINING RING.
3. REPLACE PAWLS IN PAWL POCKETS AND PUT SPRING BACK OVER THE PAWLS
BEING CAREFUL NOT TO OVERSTRETCH THE SPRING. OPENING OF SPRING
SHOULD ALIGN OVER THE PIN THAT IS PRESSED INTO THE FREEHUB BODY.
4. SET THE FREEHUB BODY DOWN WITH PAWL POCKETS FACING UP. DROP
SPACER BACK DOWN INTO OPENING ON TOP OF THE FREEHUB BODY. IT WILL
SIT ON TOP OF THE BALL BEARING THAT YOU JUST PRESSED IN. FOLLOW
THAT WITH THE NEEDLE BEARING AND NEEDLE SLEEVE WITH LIP OF NEEDLE
SLEEVE FACING UP(APPLY SOME OIL ON THE NEEDLE BEARING & NEEDLE
SLEEVE).
HUB ASSEMBLY –
1. REMOVE OLD SEAL FROM DISC SIDE END AND INSTALL NEW SEAL WITH
GROOVE SIDE FACING AWAY FROM THE HUB SHELL.
2. THREAD ON DISC SIDE END ONTO INTERNAL AXLE AND SLIDE BACK THROUGH
HUB SHELL. POUR OIL (TEFLON) INTO THE AREA WHERE THE PAWLS MEET
THE GEAR. USE ONLY OIL IN THIS AREA AS GREASE WILL PREVENT THE
PAWLS FROM PROPERLY ENGAGING.
3. TAKE FREEHUB ASSEMBLY JUST AS IT IS SITTING AND SLIDE IT BACK OVER
THE INTERNAL AXLE AND SPIN IT UNTIL IT DROPS DOWN INTO THE GEAR
AREA. BE CAREFUL NOT TO DAMAGE THE SEAL THAT IS INSTALLED IN HUB
SHELL.
4. THREAD DRIVE SIDE END BACK ON TO THE INTERNAL AXLE AND TIGHTEN
BOTH ENDS TIGHTLY. SPIN FREEHUB AND MAKE SURE THAT IT SPINS FREELY.
5. IF THERE APPEARS TO BE ANY SIDE TO SIDE PLAY IN THE HUB, THEN TIGHTEN
THE DISC SIDE LOCK RING SLIGHTLY, AGAIN BEING VERY CAREFUL AS TO NOT
OVER-TIGHTEN. THIS IS CRITICAL – AS OVER TIGHTENING THIS LOCK RING
WILL CAUSE DAMAGE TO THE HUB SHELL BEARINGS.
IF YOU HAVE ANY QUESTIONS ABOUT THE ABOVE PROCEDURES,
PLEASE CONTACT HADLEY RACING PRODUCTS